The CPE220 Wi-Fi access point is an affordable, high-quality solution for outdoor wireless connectivity. Its centralized network management software makes it ideal for point-to-point, point-to-multipoint and outdoor Wi-Fi access. Its high performance and user-friendly design make the CPE220 an ideal choice for businesses and residential users.
With enterprise-level Qualcomm Atheros chipsets, high-gain antennas and high-quality materials, a specially designed chassis and PoE power support, they make the CPE220 access point specifically designed for outdoor use and can operate flawlessly in almost any climate, with operating temperatures of -40 °C to 70 °C.
Built-in dual-polarized MIMO 12dBi 2x2 directional antenna. Dedicated metal reflector provides higher gain and less interference. The access point is designed for outdoor use and is suitable for wireless data transmission over a distance of 13 km
As the scale of the network increases, the possibility of conflicts between access points and base stations increases, which can translate into reduced throughput and negatively affect call quality. To reduce this effect, TP-LINK access points use MAXtream TDMA technology.
The CPE220 access points come with Pharos Control, a central network management software that allows easy management of all devices on the network. Detection, status monitoring, firmware updates and other network management functions can be performed using Pharos Control.
A user-friendly WEB-based operating system will allow professional users to make more precise settings.
Hardware features | |
Processor | Qualcomm Atheros 560 MHz processor, MIPS 24Kc |
Memory | 64 MB DDR2 RAM, 8 MB Flash memory |
Ports | 1 Shielded 10/100 Mbps Ethernet port (LAN0, passive PoE) 1 Shielded 10/100 Mbps Ethernet port (LAN1) 1 Grounding terminal 1 Reset button |
Power supply | Passive PoE via LAN0 ( 4.5pin; -7.8pin) Voltage: 16-27VDC |
Power consumption | Maximum 10.8 watts Note: When using passive PoE, power consumption may be higher depending on the length of the cable |
Dimensions (S x G x W) | 276×79×60 mm |
Antenna type | Built-in, dual-polarized 12dBi 2x2 directional antenna Beam width: 60° (in the H plane) / 30° (in the E plane) Note: Please refer to the datasheet for details. |
Security | Protection against electrostatic discharge 15KV Protection against lightning discharges 6KV |
Housing | ASA resistant plastic IPX5 waterproof certification |
Wireless transmission characteristics | |
Wireless standards | IEEE 802.11b/g/n (with Pharos MAXtream enabled) |
Patented protocols | TDMA mode(with Pharos MAXtream enabled) |
Wireless network speed | Up to 300Mbps (40MHz, Dynamic) Up to 144.4Mbps (20MHz, Dynamic) Up to 72.2Mbps (10MHz, Dynamic) Up to 36.1Mbps (5MHz, Dynamic) |
Frequency of operation | 2.4~2.483GHz Note: Available frequencies may vary depending on the selected region |
Transmission power | 30dBm/1000mw (Power can be varied to the nearest 1dBm) Note: Maximum transmission power may vary depending on the selected region. |
Software functions | |
Wireless network configuration | Pharos MAXtream TDMA technology 802.11b/g/n modes Channel width: 5/10/20/40MHz Automatic channel selection Transmission strength control Dynamic frequency selection (DFS) WDS enable/disable Security: WPA/WPA2, WPA-PSK/WPA2-PSK (AES/TKIP), 64/128/152-bit WEP Enable/Disable SSID Broadcasting Multi-SSID with VLAN tagging (in AP mode only) Distance/ACK Timeout settings Filtering by MAC address Advanced WiFi Settings: Beacon interval/RTS threshold/Fragmentation threshold/DTIM interval/App isolation/Short GI/Multimedia Wi-Fi. |
Management | Device detection and management via Pharos Control application Web-based management via HTTP/HTTPS System log SNMP(v2c) agent Ping Watch Dog Dynamic DDNS SSH Server |
Features of the PoE adapter | |
System Tools | Wireless signal quality indicators: Signal strength/noise/CCQ of transmission/Processor/memory Monitors: Bandwidth/Stations/Interfaces/ARP/Routes/WAN/DHCP Spectrum Analysis Speed Test Ping Traceroute |
System optimizations | IGMP Snooping/Proxy optimized for multicast applications Hardware watch dog |
Dimensions (S x G x W) | 85.8×43.9×31.9 mm. |
Ports | 1 grounded power plug 1 shielded 10/100Mb/s Ethernet port (Power Data) 1 shielded 10/100Mbps Ethernet port (Data) |
Buttons | Remote reset button |
Status of diodes | Power: Lights up green |
Input | 100-240VAC, 50/60Hz |
Output | 24VDC, 0.25A 4, 5pin; -7, 8pin. (PoE power supply, range up to 60 meters). |
Performance | >80% |
Certificates | CE/FCC/UL/IC/GS/PSB/C-tick/SAA/S-Mark/KC-mark |
Other | |
Certificates | CE, FCC, RoHS, IPX5 |
Package contents | CPE220 device Passive 24V 0.5A PoE adapter Mounting straps Power cord Quick installation guide |
System requirements | Microsoft Windows 98SE, NT, 2000, XP, Vista™ or Windows 10, Windows 8, Windows 7, MAC OS, NetWare, UNIX or Linux. We recommend using Google Chrome, Safari and Firefox browsers. We do not recommend using IE browsers. |
Work environment | Permissible operating temperature: -40℃~70℃ (-40℉~158℉) Permissible storage temperature: -40℃~70℃ (-40℉~158℉) Permissible humidity: 10%~90%, non-condensing Permissible storage humidity: 5%~95%, non-condensing |