The Tenda D301 is a wireless modem and WiFI ADSL2 + router in one, designed for both smaller businesses and home users to share their Internet connection from a DSL service provider. The Tenda D301 supports 802.11n in the 2.4GHz band, which allows communication at speeds up to 300 Mbps when configured with two antennas. The device also supports ADSL 2/ 2 + Annex B standards and thus enables communication at speeds up to 24 Mb/s download and 3.5 Mb/s upload.
The D301 is a complete solution for those who need a wired and wireless modem and router. The Tenda D301 supports ADSL 2 / 2 + Annex B standards and combines the features of an ADSL modem, wireless router and 4-port switch in one. The router has implemented a WDS function, which allows you to connect two or more access points and thus increase the range of your wireless network. The Tenda D301 can also be used as a classic Wi-Fi router with one of four RJ45 ports.
The device is equipped with two external 5dBi antennas that provide amplified signal to ensure wireless coverage of the whole house. Additionally, thanks to MIMO technology, the device uses a signal pad to reduce dead spots, providing better wireless performance, transmission speed, stability and range.
The Tenda D301 has been specially designed to effectively protect against discharges up to 6000V, making it ideal for use in areas where strong electrical discharges often occur.
The router has a number of security options, from basic protocols such as WEP (64 or 128 bit) to the latest WPA, WPA 2 and mixed WPA / WPA 2 with PSK and TKIP or AES encryption. In addition, the device has the WPS function, where the router automatically establishes a secure connection using WPA2-PSK and you do not need to know your WiFi network password.
| Technical data: | |
| Standards and protocols | IEEE802.11b/g/n IEEE 802.3, 802.3u G.994 compliant Full-rate ANSI T1.413 Issue 2 ITU-T G.992.1 (G.dmt) ITU-T G.992.2 (G.lite) ITU-T G.992.3 (G.dmt.bis) Annex A/L/M ITU-T G.992.5 Annex A |
| Interface | RJ11 × 1 Power Jack × 1 USB2.0 × 1 10/100Mbps LAN × 3 10/100Mbps WAN/LAN × 1 |
| Antenna | 5dBi External Omni directional × 2 |
| Buttons | Reset(RST) × 1 WPS × 1 WLAN On/Off × 1 Power On/Off × 1 |
| Power supply | Input: 100 - 240V 50/60Hz Output: 9V1.0A |
| Dimensions | 157.8 × 105.2 × 29.4mm |
| LED | PWR, SYS, INTERNET, USB, WPS, WLAN, 4/iTV, LAN3, LAN2, 1/WAN, DSL |
| Wireless connection speed | 300Mbps |
| Frequency | 2.4GHz |
| RF power supply | |
| Wireless connection security | Wireless MAC Filtering Support 64/128 bit WEP WPA-PSK/WPA2-PSK WPS |
| Type of connection | PPPoE, PPPoA, IPoA, MER, Bridge |
| Mode of operation | Wireless Modem Router, Wireless Router |
| Advanced features | PVC Configuration MAC Clone DSL Settings Interface Grouping QoS USB Sharing(Samba) Parental Control IPTV |
| USB sharing | Storage Sharing( Samba) |
| Security | IP Filter MAC Filtering |
| IPv6 | Support 6RD & DS-Lite, IPv6 and IPv4 dual stack |
| Management | LAN IP Setting Backup & Update & Restore to factory default Logs System SNMP Agent TR-069 Client Internet Time Access Control Update Software via web, TFTP & FTP Diagnostics DDNS, IGMP Multicast, VLAN, 802.1Q, Routing |
1. Opem your web browser and enter 192.168.1.1 into the address bar and press Enter. The username and password are „ admin ” by default.
2. After you log into the web interface, for dial-up PPPoE mode, select Ethernet in Link Type and PPPoE in Connection Type and then type in the username and password.
For Bridge mode, select Ethernet for Link Type and Bridge for the Connection Type.
For static mode, select Ethernet in Link Type and IPoE in Connection Type, then input the IP address, subnet mask and the Primary DNS.
3. Save changes and check the connection status.
