ZTE F623 | ONT | WiFi, 1x GPON, 3x RJ45 100Mb/s, 1x RJ45 1000Mb/s, 1x RJ11, 1x USB
Extralink Piorun 2000VA/1600W | Power inverter | pure sine wave, battery voltage 24VDC
Extralink EFL-1031 Odin | LED Flashlight | rechargeable battery, 10W, 400lm
Extralink ARES | PoE Switch | 16x Gigabit PoE/PoE+, 2x SFP, 1x Console, 150W, Managed
Extralink Premium 12U 600x600 Black | Rack cabinet | tool-free mounting, wall-mounted
Extralink Pilot 9mm 150m | Cable pulling rod | glass fibre FRP, d. 9mm, l. 150m, yellow
Ubiquiti AMO-3G12 | Omnidirectional antenna | airMAX, 3GHz, 12dBi
Extralink Olivia | Fiber optic termination box | 2 core, with pigtail and SC/APC adapter
Totolink N300RT V4 | WiFi Router | 300Mb/s, 2,4GHz, 5x RJ45 100Mb/s
Extralink Plinth 800x1000 Black | Plinth for standing network cabinets |
Aqara Smart Wall Switch H1 Gray | Wall Switch | Dual, with neutral wire, Zigbee 3.0, EU, WS-EUK01-G
Use the precision alignment device with any of these antennas: airFiber® AF-5G30-S45, PowerBeam™ PBE-5AC-620, PowerBeam PBE-M5-620 and RocketDish™ RD-5G30-LW.
The kit enables and facilitates precise positioning of AirMAX class parabolic antennas. PAK-620 Precision Alignment Kit for Ubiquiti antennas of 620mm diameter. Precise two-axis alignment improves beam directionality.
| Basic technical parameters | |
| Dimensions | 9.9×6.0×9.9 cm |
| Quick manual | Download |
This instruction shows the mounting to a RD-5G30-LW, but it is also applicable for other 620 mm antennas.
1. Loosen the four hex head bolts of the Alignment Bracket Assembly.
2. Lift the Elevation Alignment Bracket up and out to separate it from the Azimuth Alignment Bracket.
3. Use four Hex Head Bolts to attach the Elevation Alignment Bracket to the antenna. Ensure that the Hex Head Bolts go through the Elevation Levers on the inner sides of the Elevation Alignment Bracket.
4. Attach two Pole Clamps to the Azimuth Alignment Bracket:
a. Insert four Carriage Bolts into the Azimuth Alignment Bracket.
b. Slide the hole of a Pole Clamp over one bolt of each pair.
c. Place one Serrated Flange Nut on each bolt.
5. Attach the Azimuth Alignment Bracket to the pole:
a. Slide the slot of each Pole Clamp over the corresponding Carriage Bolt.
b. Tighten the four Serrated Flange Nuts to secure the Azimuth Alignment Bracket to the pole.
6. Attach the Elevation Alignment Bracket to the Azimuth Alignment Bracket:
a. Insert the four hex head bolts of the Elevation Alignment Bracket into the slots of the Azimuth Alignment Bracket.
b. Slide the Elevation Alignment Bracket down, and tighten the four hex head bolts to 25 N-m.
7. Before adjusting the azimuth and elevation angles, ensure that these eight hex head bolts are loose enough to allow movement.
8. To adjust the azimuth angle up to ±15°, turn the Azimuth Adjustment Screw until the desired angle is reached.
9. To adjust the elevation angle up to ±15°, turn the Elevation Adjustment Screw until the desired angle is reached.
10. Lock the alignment by tightening the eight hex head bolts to 25 N-m.
Precision mounting kit dedicated for airMAX class parabolic antennas
